Sunday, 18 November 2012

Heat Can Stop Your Machines

When hot weather causes the electronics inside a control cabinet to fail,there is a panic to get the machinery up and running again. There are several cooling options out there and it’s important to know the facts.

Sunday, 28 October 2012

Super Air Knife for Blowing And Cleaning

Exair’s Compressed Air products   provide solution for Industrial Automation  for various applications in small  and big factories. One of our customers uses  the 18” super Air knife for  blowing and cleaning  water and dust particles from fruits. 

They had a serious problem relating to their fruit drying and cleaning purpose. So they contacted us. Our application engineer visited their site and determine a solution  to their problem .  Earlier they were doing this work by  the electric fans ,but it was time taking and not so effective as they couldn’t clean the dust properly. As per his consideration we provided them a 18” Super Air knife. Now they are satisfied by using EXAIR’s Super Air Knife.

Wednesday, 24 October 2012

What You Don't Know Can Kill You!

Did you know that it's dangerous to block a typical commercial nozzle with your hand or other body part? According to the Occupational Safety and Health Administration (OSHA), any air hose, open pipe, or tube with an outlet pressure greater than 30 PSIG could potentially injure or even kill someone who blocks the opening with a body part (OSHA CFR 1910.242(b)). The dead-ended pressure buildup could force air bubbles into a worker's bloodstream and block critical blood flow. EXAIR's engineered Air Nozzles are designed to prevent dead-ending at any pressure. >> Tell Me More

Are You Blowing Away Money With Your Current Blowoff Operation?

Many commercial nozzles ignore efficiency in order to try and create additional blowoff force. While this may be useful in the short term, it can ending up costing you a lot of money over the life of that nozzle! For example, a typical 1/8" open pipe blowoff at 80 PSIG will use 70 SCFM of air. EXAIR's equivalent 1/8 NPT Model 1102 Mini Super Air Nozzle will use 10 SCFM at 80 PSIG. In other words, after using EXAIR's engineered nozzle over one year of a 40 hour/week operation, you could save about Rs 1,26,000.00 in compressed air production and that's just by replacing one nozzle! >> Tell Me More

In addition, the reduced air use of an EXAIR engineered nozzle also means that less noise is produced. When a blowoff operation is upgraded with an EXAIR Air Nozzle, noise is reduced by 10 dBA on average! >> Tell Me More

Thursday, 11 October 2012

E-Vac Vacuum Generators

E-Vac Vacuum Generators

XAIR’s compressed air powered E-Vac is a low cost, compact alternative to traditional vacuum pumps in single stage designs. EXAIR's vacuum generators can be used to generate vacuum economically without a single moving part.
Patented design extracts maximum amount of energy from compressed air source while optimizing the level of vacuum generation. E-Vac is commonly used for pick & place operations and provides instantaneous response. Variety of sizes & flows along with a selection of suction cups for wide range of application are available with these single stage vacuum pumps.

The E-Vac vacuum generators have high efficiency & have been engineered to minimize air consumption. The fluctuations in vacuum are eliminated due to the EXAIR’s single stage design, providing consistent & steady vacuum. E-Vac has no moving parts to wear out & is completely maintenance free.More details>>

Thursday, 27 September 2012

Safety Air Guns with Chip Shields Protect Operators

           EXAIR’s family of Safety Air Guns (Precision Safety Air Gun, Soft Grip Safety Air Gun, and Heavy Duty Safety Air Gun) has always provided high quality performance for your blowoff, drying or cleaning needs. Now, they are available with Chip Shields to protect workers and to help businesses comply with OSHA safety standards. Chip Shields can be used on Safety Air Guns with or without an extension pipe.

            Chip Shields are a durable polycarbonate shield that protects operators from flying debris often associated with blowing chips off machined parts. Chip Shields are great for keeping coolant from splashing everywhere during drying operations.Chip Shields are available to fit the Safety Air Guns you currently have in use.

         EXAIR’s Safety Air Guns use engineered air nozzles for high performance and safety – designed to maximize entrainment of room air while minimizing compressed air consumption. The Precision Safety Air Gun is extremely lightweight and the most comfortable to operate during periods of extended use. The Heavy Duty and Soft Grip Safety Air Guns have a durable cast aluminum body for rugged industrial use. All are available with extension pipes and Chip Shields

Friday, 21 September 2012

Siphon Fed Spray Nozzles for Non- Pressurized Applications

EXAIR's new siphon fed spray nozzles atomize fluids in a range of spray patterns for a wide variety of uses. Siphon fed atomizing nozzles require no liquid pressure and can be used with gravity fed liquids or lift liquids from a siphon height as much as 36 inches (91cm). They combine liquid and compressed air to create a thin coating of liquid that can be easily adjusted to meet the needs of your application.

With EXAIR’s siphon fed atomizing nozzles, you can coat, cool, treat and paint a variety of products using compressed air and liquids with a viscosity of up to 200 centipoise. Used with water, atomizing nozzles are an efficient way to evenly cool hot items in your automated process.

The stainless steel construction of these atomizing nozzles adds to their durability and corrosion resistance. EXAIR atomizing nozzles are available in a variety of flow patterns and rates to meet your needs. Internal mix and external mix atomizing nozzles are also available. All models are adjustable.

Contact Vivek Engineers for more information. 


Wednesday, 29 August 2012

Standard Air Wipe

This hard-hitting 360° ring of airflow is the economical way to blowoff, dry, clean and cool.

EXAIR’s Standard Air Wipe provides a uniform 360° airstream that is ideal for blowoff, drying, cleaning and cooling of pipe, cable, extruded shapes, hose, wire and more. The split design offers easy clamping around the surface of the material moving through it, eliminating the need for threading. All models include painted screws and plastic shims. Reinforced rubber hose is also included on sizes up to 4" (102mm) for added corrosion and heat resistance. Standard Air Wipe models are rated for temperatures up to 150°F (66°C) .

 The Standard Air Wipe is an economic choice when the added properties of stainless steel are not required. The Standard Air Wipe is generally suited to non-corrosive applications where temperatures do not exceed 150°F (66°C).The Standard Air Wipe includes painted screws, plastic shims & a general purpose PVC coupling air hose on sizes up to 4”(102 mm).It meets OSHA maximum dead end pressure & noise requirements.
Contact Vivek Engineers for more information.



Thursday, 16 August 2012

Full-Flow Air Knife

EXAIR’s Full-Flow Air Knife is a cheapest & energy competent way to clean, dry or cool parts, webs or conveyors. Full-Flow Air knives operate by entraining the surrounding air along with the compressed air utilizing the “Coanda” effect to produce high flow, high velocity curtain of air. Air Knives are designed for 24/7 use, have smooth edges and shims for easier cleaning, can be precisely adjusted without tools for faster change-over’s and are custom sized for your application. The Full-Flow feature provides air flow across the entire length. The Full-Flow Air Knife has the compressed air inlet on the rear. It is available in either aluminium or stainless steel construction.

Shim Sets 

A Full-Flow Air Knife has a .002" (.05mm) gap setting. This gap is set with a shim positioned between the cap and the body of the Full-Flow Air Knife. Force and flow through the Full-Flow Air Knife may be easily increased by adding shims to open the gap. Kits include a shim set. Shim sets for aluminum Full-Flow Air Knives include a .001" (0.03mm), .003" (0.08mm) and .004" (0.10mm) thick plastic shim. Shim sets for stainless steel Air Full-Flow Knives include (1) .002" (0.05mm) thick stainless steel shim.

Contact Vivek Engineers for more information.

Thursday, 9 August 2012

CE Compliant Air Amplifier

EXAIR’s Super Air Amplifiers and Adjustable Air Amplifiers have always provided a fast, quiet, efficient way to move large volumes of air for the transport of smoke, fumes, or light materials as well as for venting, cooling, drying and cleaning. Now, independent laboratory tests certify that EXAIR’s Air Amplifiers meet the rigorous safety, health, and environmental standards of the European Union in order to attain the CE mark.

Using no electricity or moving parts, EXAIR’s Air Amplifiers are able to transform a small amount ofcompressed air into a high volume, high velocity output that is up to 25 times their consumption rate.  The patented design maintains a constant, high velocity outlet flow across the entire cross sectional area. Output is easily adjusted and both the vacuum and discharge ends can be ducted. Air Amplifiers are available in stock in both aluminum and corrosion resistant stainless steel. 

Contact Vivek Engineers for more information.

Tuesday, 7 August 2012

CE Compliant Control Minimizes Compressed Air Use

EXAIR’s digital ETC (Electronic Temperature Control) Cabinet Cooler System keeps electrical enclosures cool while minimizing compressed air use. Independent laboratory tests now certify that the ETC™ is CE compliant to assure safe operation in a wide range of cooling applications, allowing it to work perfectly with our CE compliant Cabinet Cooler units.

The ETC accurately maintains a constant temperature in the electrical enclosure that is slightly under the maximum rating of the electronics. It permits just enough cooling for the electronics without going so cold as to waste compressed air. A digital LED readout displays the temperature of the electrical enclosure (°F or °C), then displays the user temperature setting when pressing the “push to set” button. When that setting is exceeded, the Cabinet Cooler System is activated which circulates 20°F air throughout the electrical enclosure to prevent a high temperature malfunction.

The ETC is suitable for NEMA 4, 4X and 12 environments with a strong polycarbonate plastic housing and sealed membrane push button control. All systems include an automatic drain filter separator to keep moisture in the compressed air out of the electrical enclosure. Models for 120 VAC or 240 VAC are available with cooling capacities up to 2800 Btu/hr. Applications include cooling programmable controllers, CNC panels, computer cabinets, and variable speed drives.

Vivek Engineers
Website :
Follow us:

Wednesday, 11 July 2012

USB Data Logger Available for Digital Flowmeter

EXAIR’s Digital Flowmeter provides an excellent way to monitor compressed air consumption and waste. Now, with the addition of EXAIR’s new USB Data Logger, you can also maintain a history of the Digital Flowmeter’s measurements for analysis.Use the included software to configure the Data Logger to record your flow rate. Record from once a second (about nine hours of data) up to once every 12 hours (over 2 years!).

Regular monitoring of compressed air usage makes it possible for companies to save thousands of dollars per year in compressed air waste by identifying costly leaks or inefficient air products. When the Data Logger is removed from the Digital Flowmeter and plugged into a computer, the data can be viewed in the included software or exported directly into Microsoft Excel®. This allows you to track flow rate easily on your computer.

The Data Logger is available pre-installed on the Digital Flowmeter.Summing Remote Displays, that make it easy to monitor compressed air consumption from a convenient location, are also available.

Vivek Engineers,E- mail : ,Website:

CE Compliant Air Nozzles Increase Efficiency

EXAIR’s family of Air Nozzles-- from the tiny new Model 1108SS Atto Super Air Nozzle at 2.0 ounces (56.7 grams) of blowing force to the high powerModel 1120 Large Super Air Nozzle at 23 pounds (10.4 kg) of strong blowoff force -- have always provided safe, economical performance. Independent laboratory tests now certify that EXAIR’s entire Air Nozzle family hasalso met the rigorous safety, health, and environmental standards of the European Union in order to attain the CE mark.

By entraining high volumes of room air, EXAIR’s Super Air Nozzles use less compressed air and less energy to provide superior performance to other blowoff products. Unlike open pipe and nozzles that haven’t been optimized, none of EXAIR’s large selection of Super Air Nozzles can be blocked, meeting OSHA’s standard for dead-end pressure 29 CFR 1910.242(b). All of EXAIR’s Super Air Nozzles also fall within OSHA’s noise requirement 29 CFR 1910.95(a).

Vivek Engineers

Wednesday, 25 April 2012

Cold Gun Increases Tool Life

Cold Gun Increases Tool Life

A Company manufactures intricate machined parts for the automotive, motorcycle and aerospace industries. One of their machinists had a frequent problem rough-milling pocket in type 410 stainless steel when using a two flute 3/8" carbide cutter on their Okuma vertical machining center. Coolant produced thermal shock, resulting in micro cracking of the carbide inserts. Without coolant, thermal cracking of the inserts was almost immediate. They were constantly changing inserts.

The company installed a Model 5215 Cold Gun System. The 20°F cold air kept the inserts cool and allowed all the heat to be carried away on the chips. Tool life increased by 50%.

The Cold Gun incorporates a vortex tube to convert an ordinary supply of compressed air into two low pressure streams, one hot and one cold. The hot airstream is muffled and discharged through the hot air exhaust.  The cold air is muffled and discharged through the flexible hose, which directs it to the point of use.  The magnetic base provides easy mounting and portability. COLD GUN

Heat buildup can ruin expensive tooling as well as the part being machined. In this situation, it would have been easy to constantly ruin a Rs.9000 cutter. When asked how others solve this problem, the machinists replied, "We've seen companies go so far as to defeat the safety interlocks so the machine runs with the doors open - just to blow a little compressed air at the part to cool it. For us, the Cold Gun keeps the tooling cool and allows us to immediately handle the part since the heat blows away with the chips.